Car engine carbon removing machine better protection for car engine

Today's automotive industry adopts high technology to design
complex fuel metering and combustion control engines, and uses
computer monitoring to make the engine run at an unimaginable level
of precision, which not only makes the car more fuel efficient, but
also greatly reduces engine exhaust emissions. However, the more
sophisticated the engine is manufactured, the lower the tolerance
of the engine is. If the fuel system
and the combustion system are fouled, the engine efficiency will be
reduced immediately, which will seriously affect the driving
performance.
The three areas where are most prone to be fouled in the engine:
1.Fuel System
2.Injector needle valve
3.Combustion chamber—including cylinders, pistons, cylinder heads,
valve assemblies,
and intake valves.
Engine Fouling and effects:
The fouling generated by the engine includes: Gum, Shellac, Varnish
and Carbon. Due to the difference in the quality of the gasoline,
the incorrect driving habits, stopping due to congestion and poor
air quality and other factors will inevitably lead to the formation
of combustion pollutants in the engine. These pollution deposits
are first produced by the fuel injector needle valve because the
diameter of the needle valve is 0. 0 0 2 inches. It is equivalent
to the size of human hair. Once the fouling forms a blockage, it
will immediately affect its original atomization spray oil supply
performance. As long as 10% of the fuel supply is restricted, the
fuel can't be burned completely , which also increases carbon
deposit. When the carbon accumulation in the engine reaches a
certain level, the entire oil supply system is not smooth, the
engine function is attenuated, causing jitter in acceleration, weak
power even fuel is consumed, and difficulty in starting,
intermittent flameout, harmful exhaust emissions and temperature
rise, driving performance will gradually decline. Experiments have
shown that additives can penetrate into the engine to cause
deposits, especially intake valves. At this time, it is not only
difficult but also costly and time-consuming to eliminate these
deposits. In addition, the function of the additive is limited in a
short time. It may have other effects on the engine, such as oil
gelation or waxing, fuel pump premature wear, engine operating
temperature rise, and increasing amount of contaminant dissolved in
the tank. Other engine carbon removal methods, such as drip, spray
and disassembly, are not only limited to carbon removal partial
area, but also are too time consuming (the engine takes one to two
days to disassemble), and it cannot achieve economic and
profitability demand. The GX-8 0 A Free-dismantling engine fuel
system cleaning machine developed by our company, combined with the
most effective patented carbon removal cleaning agent, is the best
tool for solving the engine carbon deposit. It can be used with
regular car maintenance and special carbon removal. No need
disassemble the engine, only use the connector to connect with the
engine oil supply pipe, plug the engine return pipe with a plug,
and add a fixed fuel mixture carbon removal agent, let the
decarburizer enter under the normal operating conditions of the
engine. It can dissolve the carbon deposits, colloidal and lacquer
pollutants in the injector needle and combustion chamber components
within 30 minutes, and then release them from the vehicle exhaust
system through the cycle decomposition process. The process can
recover the vehicle performance ,make the start smoothly and easily
to accelerate, save fuel and reduce air pollution. When should we
remove the carbon deposit in engine?
In modern times, it is necessary to clean carbon deposits in every
50,000 to 2 - 2 0 0 0 0 km driving so that the engine can play the
performance of the new car from time to time. Engine fuel system
free-dismantling cleaning machine is a revolutionary improvement
method.
Parameters of GX-8 0 A :
Voltage : DC12V,
Display precision : 2 million pixels
Noise:<70dp
Return Pipe : 2.5m
Net Weight : 30kgs
Dimension: 430*400*1000mm
Pressure gauges : 0-1.6MPA
Max Power : 150W
Endoscope accuracy : 1.3 million pixels
Foam tube : 2.5m
Function: |
Clean fuel injector, |
Clean air intake system |
Clean TWC, |
Clean combustion room, |
With endoscope
|

This machine supplies better protection for engine than HHO machine
which will generate high temperature.